Inside a phone

A phone is a whole computer on one board

11System on a chipprocessor, graphics and memory in one package22Storageflash memory soldered to the board: no upgrades33Batterylithium-ion: the largest part, and the first to wear out44Radioscellular, Wi-Fi, Bluetooth, NFC and GPS, with their antennas55Camerasfront and back66PortUSB-C: charging, data and video77ScreenOLED or LCD under a touch layer, covering the whole frontA phone is a complete computer on one board, and almost nothing in it can be upgraded.What a technician replaces is the battery, the screen and the charging port. Everything else is one board.A swollen battery is a fire risk: stop using the device and do not press on it.

The same parts as a PC, soldered together. The battery takes the most room.

Inside a phone · Going deeper

What can be replaced in a laptop

Laptop partFormWorth knowingMemorySO-DIMM modules, or solderedcheck which before promising an upgradeStorageM.2 SSD, or a 2.5-inch driveusually the easiest upgradeBatteryan internal pack, screwed or glued inreplace when the runtime collapsesWireless cardan M.2 card with two antenna leadsthe antennas run up beside the screenScreenan LCD or OLED panel on one thin cablematch the exact panel and connectorKeyboarda ribbon cable to the boardthe usual victim of spilled drinksA laptop sits between a desktop and a phone: some parts swap, some are soldered.Disconnect the battery before touching anything else, keep track of every screw, and follow the maker'sservice manual. A docking station or port replicator adds the ports a thin laptop lacks.

Memory, storage and battery usually swap. Check for soldered parts first.

Wireless

Each radio suits one distance

RadioReach. Each mark is ten times the one before.1 cm10 cm1 m10 m100 m1 km10 kmNFCtap to pay, door badges4 cmBluetoothheadphones, watches, keyboards10 mWi-Fithe local networkabout 50 m indoorsCellular: 4G, 5Ginternet and calls anywherekilometresGPSreceives only, from satellites 20,200 km up: it tells the phone where it isEach radio suits one distance, and the shorter the reach, the less power it draws.A Bluetooth accessory is paired once: make it discoverable, choose it on the phone, confirm the code.A hotspot shares the cellular connection over Wi-Fi. Airplane mode turns every transmitter off.

NFC reaches centimetres, Bluetooth metres, Wi-Fi a building, cellular kilometres.

Sync and management

The data lives in the account

PhoneThe accountmail, contacts, calendar, photossyncLaptopsyncCompany MDMdevice management✓require a screen lock✓encrypt the storage✓install company apps✓wipe it remotely if lostThe data lives in the account, so a lost phone is a lost device, not lost data.Microsoft 365, Google and iCloud accounts keep mail, contacts, calendars and photos on every signed-indevice. Mobile device management (MDM) lets a company enforce rules on phones it owns, and on personalones used for work (BYOD), where it can wipe only the company's part.

An account keeps every device the same. MDM applies the company's rules.

Printers

Two questions sort out any printer

Computeryou press PrintQuestion 2How does the jobreach the printer?by cable or over the networkPrinterQuestion 1How does it puta mark on paper?ink, toner, heat or pinsThe pagePrinters are a regular part of support work, and every printer fault answers to one of two questions.How does it put a mark on paper? That decides the supplies it uses and the faults you see on the page.How does the job reach it? That decides what to check when nothing comes out at all.

Ask how it marks the paper, and how the job reaches it. Every printer fault is one or the other.

Printer types

Four ways to put a mark on paper

TypeHow it marksConsumablesBest atTypical faultLasertoner powder, fused by heattoner, drum, fuservolume textsmears, ghost imagesInkjetsprays drops of liquid inkink cartridges, print headphotos and colourstreaks: clogged nozzlesThermalheats coated paperthermal paper onlyreceipts and labelsfaint: a dirty print headImpactpins strike an inked ribbonribbon, continuous papermulti-part carbon formsfaded: a worn ribbon3Dbuilds plastic in layersfilament or resinparts and prototypesfirst layer will not stickFour ways to put a mark on paper, each with its own consumable and its own fault.Inkjets are cheap to buy and dear to run; lasers are the reverse. An inkjet left unused dries out: run itscleaning cycle. Thermal printers need no ink at all, which is why every till uses one.

Laser fuses powder. Inkjet sprays ink. Thermal heats paper. Impact strikes a ribbon.

Laser printing

A laser printer draws with light, then powder, then heat

1 Light draws the pageA laser writes the page ontoa rolling drum as an invisiblepattern of static charge.2 Toner sticks to the drawingToner, a fine powder, clingsonly where the laser wrote,then passes to the paper.3 Heat fixes itHot rollers melt the powderinto the paper. That is whypages come out warm.A laser printer uses no ink. It draws with light, picks up powder where it drew, and melts the powder into the page.Knowing the three steps tells you where a fault is: a blank page, a smear that rubs off and a repeated mark each point to one.The full process has seven named steps, which the A+ exam asks for in order. Go deeper for all seven.

A laser draws the page as static charge, toner sticks to it, and heat melts the toner into the paper.

Laser printing · Going deeper · 1 of 2

Laser printing in full: seven steps around one drum

DrumpaperController11Processingthe page becomes a map of dotscharge roller22Chargingthe drum gets an even charge33Exposingthe laser writes the imageToner44Developingtoner sticks where the laser hittransfer roller55Transferringtoner jumps to the paperfuser66Fusingheat and pressure melt it inblade77Cleaningthe drum is wiped cleanA laser printer draws the page in static electricity, then fixes powder to it with heat.The order never changes: processing, charging, exposing, developing, transferring, fusing, cleaning.Each fault points at one step, which is what makes the cycle worth knowing. The fuser is hot enough to burn.

Charge the drum, write with the laser, add toner, transfer, then fuse with heat.

Laser printing · Going deeper · 2 of 2

Faults, step by step

What the page showsStepCause and cureToner rubs off the pageFusingthe fuser is not hot enough: replace itFaded printDevelopingtoner is low: replace the cartridgeBlank pagesTransferringtransfer roller failed, or the cartridge seal is still onAll-black pagesChargingthe charge roller or corona wire failedA faint repeat of the image down the pageCleaningthe drum was not wiped: replace drum or cartridgeA line down every pageExposinga scratched drum or a dirty laser windowPages of random charactersProcessingthe wrong driver: install the right onePaper jams and misfeedsPaper pathworn pickup rollers, or damp paperRead the page, name the step, replace that part.A maintenance kit (fuser, transfer roller, pickup rollers) is fitted at the page count the maker sets.

Toner that rubs off: fusing. Faded: developing. Ghosts: cleaning.

Printing on a network

One stuck job blocks the whole queue

Print queue (the spooler)invoice.docxwaitinglabels.xlsxwaitingphoto.jpgwaitingPrintertakes one job at a timereport.pdfErroridle: nothing arrivesEvery job waits in a queue, and one stuck job blocks all the rest.Cancel the stuck job; if it will not go, restart the Print Spooler service. A network printer needs a fixedaddress, or it vanishes when the address changes. Each system needs the right driver. Settings such asduplex, tray and paper size live in the driver, so check them when output is not as expected.

Jobs wait in the spooler and print in order. A failed job holds up the rest.

Lesson complete

You finished “Mobile devices and printers”

Nicely done.

Open in a new tab