Wi-Fi bands
More spectrum means more speed and less reach
2.4 GHz reaches furthest. 5 GHz is faster. 6 GHz is fastest and shortest.
Wi-Fi uses three bands of radio, and they are very different sizes. Two point four gigahertz is a narrow strip. Its signal travels far and passes through walls, but it is crowded and slow. Five gigahertz has about seven times as much room. It is faster, with far less interference, but does not reach as far. Six gigahertz is larger again. It is the fastest and the emptiest, and has the shortest reach. Only newer devices can use it.
Wi-Fi bands · Going deeper
Channels 1, 6 and 11
Only 1, 6 and 11 do not overlap on 2.4 GHz.
Wi-Fi standards
From 11 megabits to 9.6 gigabits in six steps
b, a, g, then n (Wi-Fi 4), ac (Wi-Fi 5) and ax (Wi-Fi 6).
Each Wi-Fi standard has a letter, a band and a top speed. On this scale, every mark is ten times the one before. The first three are old: B on two point four gigahertz, A on five, and G back on two point four. N, also called Wi-Fi four, was the first to use both bands. A C, Wi-Fi five, uses five gigahertz only, and reaches gigabit speeds. A X is Wi-Fi six. It uses both bands, and Wi-Fi six E adds six gigahertz.
Wi-Fi standards · Going deeper
Bluetooth, NFC, RFID and fixed wireless
NFC, RFID, and licensed against unlicensed.
Check yourself
These are the eleven 2.4 GHz channels, to scale. Which three should a technician use?
IP settings
Four settings put a computer on the network
An address and mask, a gateway to leave, and DNS for names.
Every computer on a network needs four settings. An I P address, and a subnet mask. The mask shows which part of the address names the network, and which part names this computer. A default gateway: the address of the router, which is the way out to everywhere else. And a D N S server, to turn names into addresses. One address to recognise on sight: anything starting one six nine, two five four. It means the computer asked for settings and nobody answered.
IP settings · Going deeper
Private, public and special addresses
Three private ranges, APIPA, loopback and IPv6.
DHCP
Scope, lease, reservation, exclusion
The scope is the range. A reservation is a fixed address. An exclusion is held back.
D H C P hands out those settings, and it has four words to learn. The scope is the whole range of addresses the server looks after. Most of it is a pool. Each address is lent out as a lease, for a set time. An exclusion is a part of the range the server never hands out. The router and the servers sit there, with addresses set by hand. A reservation is one address always given to the same device. Here, the printer.
DHCP · Going deeper
DNS records, VLANs and VPNs
A, AAAA, CNAME, MX, TXT.
Check yourself
What does this address tell you?
Network hardware
Modem, router, switch, access point: one job each
The modem converts, the router routes, the switch connects, the access point adds Wi-Fi.
Follow the internet into an office, one box at a time. First, a modem. It converts the provider's line, whether cable, telephone or fibre, into Ethernet. Then a router, with a firewall. It joins the office network to the internet, and filters what may cross. Then a switch, with a port for each wired device. From the switch, cables run to an access point, which the switch can also power, and through a patch panel to the wall sockets, for computers and printers.
Network hardware · Going deeper · 1 of 2
Switches, PoE and modems
Managed against unmanaged; PoE at 15.4, 30 and 90 W.
Network hardware · Going deeper · 2 of 2
Clue words for wireless, addressing and hardware
1, 6, 11, APIPA, reservation, PoE.
Check yourself
What should the technician use?
Lesson complete
You finished “Wireless, addressing and network hardware”
Answer the questions along the way to see your score here.