2.4 GHz channels
Only three 2.4 GHz channels do not overlap
At 2.4 GHz, channels sit 5 MHz apart but are 20–22 MHz wide, so only channels 1, 6 and 11 do not overlap.
Wi-Fi shares radio bands with everything else. The 2.4 gigahertz band is divided into channels five megahertz apart, but a Wi-Fi signal is twenty megahertz wide, so most channels spill into their neighbours. Only three fit side by side without touching: one, six and eleven. Every 2.4 gigahertz design uses those three and nothing else.
2.4 GHz channels · Going deeper
The 5 GHz and 6 GHz bands
5 GHz has 25 channels of 20 MHz in the US, 6 GHz has 59; channel width trades speed for the number of channels. DFS avoids radar.
Signal
Higher bands carry more but reach less
Over 10 m, 6 GHz loses 8.5 dB more than 2.4 GHz. Aim for RSSI of −67 dBm or better and 25 dB SNR.
Radio fades with distance, and faster at higher frequencies. Over ten metres of open air, a 2.4 gigahertz signal loses about sixty decibels; a 6 gigahertz signal about sixty-nine, roughly seven times less power arriving, before any walls. Signal is measured in dBm, negative numbers where closer to zero is stronger. Voice and video need about minus sixty-seven, and twenty-five decibels above the noise.
Signal · Going deeper
Antennas focus the signal
Omnidirectional antennas cover all around; directional patch, Yagi and dish antennas trade width for reach. Gain is in dBi.
Wi-Fi standards
Each Wi-Fi generation is faster, but the air is shared
Wi-Fi 6 (802.11ax) tops out at 9.6 Gbps and Wi-Fi 7 (802.11be) at 46 Gbps, but radio is half duplex and shared by every client.
Each new standard raised the ceiling. The early ones, b, a and g, ran at eleven and fifty-four megabits. Wi-Fi 4 and 5 added multiple antennas and wider channels: six hundred megabits, then nearly seven gigabits. Wi-Fi 6 reached nine point six, and Wi-Fi 7 forty-six. Those are lab numbers. A phone gets a fraction, and shares the channel with everyone else, because only one device can talk at a time.
SSID and roaming
One network name, many access points
The SSID is the network name; each AP radio has its own BSSID; APs sharing an SSID form an ESSID that clients roam across.
An access point announces a network name, the SSID, Corp. Its radio has a MAC address, the BSSID. Two more access points announce the same name, each with its own BSSID, on different channels. Together they are one extended network. A phone walking down the corridor moves to whichever access point it hears best, and keeps its connection.
SSID and roaming · Going deeper
Infrastructure, ad hoc, mesh and point to point
Infrastructure mode uses APs; ad hoc links devices directly; mesh APs relay wirelessly; point to point bridges sites.
Wireless security
Enterprise Wi-Fi gives every person their own key
Use WPA3 (or WPA2 with AES). Personal mode shares one key; Enterprise mode checks each user with 802.1X and RADIUS.
Open networks and the old WEP and WPA are readable by anyone. WPA2 with a shared password is common, but a captured login can be guessed offline. WPA3 closes that gap. In a company, Enterprise mode is the answer: each person signs in with their own account or certificate, the access point checks it with a RADIUS server, and one leaver can be switched off without touching anyone else.
Controllers
Lightweight access points are run by a controller
Lightweight APs tunnel to a WLC with CAPWAP (UDP 5246 and 5247) and sit on access ports; autonomous APs are configured one by one.
Small networks use autonomous access points, each configured on its own, usually on a trunk port carrying the VLANs of every network name. Larger networks use lightweight access points and a wireless controller. Each access point builds a tunnel to the controller, which configures, secures and tunes them all from one place. Because traffic travels inside the tunnel, the access point’s switch port is a plain access port.
Controllers · Going deeper
AP modes and controller ports
AP modes: local, FlexConnect, monitor, sniffer, bridge. WLC dynamic interfaces map each WLAN to a VLAN on the distribution trunk.
Site survey
A site survey places APs to overlap a little and never share a channel
A site survey produces a heat map; cells overlap 15–20% for roaming, neighbours use different channels, and interference sources are found.
Three access points cover this floor on channels one, six and eleven. Their cells overlap by fifteen to twenty percent, so a phone can move from one to the next without dropping. A survey measures the real building and finds what goes wrong: two access points on the same channel, a microwave oven, Bluetooth, a rogue access point someone plugged in, or a dead spot behind the lift shaft.
Lesson complete
You finished “Wireless networks”
Nicely done.