| Host / client / server | Any device with an address / the one that asks / the one that answers | Hosts and addresses |
| Switch, router, access point, firewall | Connects one network / connects networks / adds Wi-Fi / filters traffic | Network devices |
| Hub, switch, router | Layer 1 repeats bits, layer 2 forwards frames, layer 3 routes packets | Network devices |
| Collision / broadcast domain | Split by every switch port / by every router port | Network devices |
| Unicast, broadcast, multicast, anycast | One receiver, everyone on the link, a subscribed group, the nearest of many | Traffic types |
| Cat 5e / 6 / 6A / 8 | 1 Gbps at 100 m / 10 Gbps at 55 m / 10 Gbps at 100 m / 40 Gbps at 30 m | Copper cable |
| T568A / T568B | Two pin orders; the same at both ends makes a straight-through cable | Copper cable |
1000BASE-T | Speed 1000 Mbps, baseband signalling, T for twisted pair | Copper cable |
| Plenum / riser | Jacket for air-handling spaces / between floors | Copper cable |
| Multimode / single-mode | Short runs with cheaper optics (OM3 300 m, OM4 400 m at 10G) / 9 µm core, kilometres | Fibre |
| LC SC ST MPO | Fibre connectors: small duplex, square push-pull, bayonet, many fibres in one | Fibre |
| SFP / SFP+ / SFP28 / QSFP28 | 1G / 10G / 25G / 100G pluggable modules | Transceivers |
| PoE 802.3af / at / bt | 15.4 W / 30 W / 60 to 90 W at the switch port | Power over Ethernet |
| Power budget | The switch's total PoE; the last device asking may stay dark | Power over Ethernet |
| 200,000 km/s | Light in fibre: 5 µs per km, 1 ms per 200 km one way | Distance and delay |
| OSI 7 to 1 | Application, presentation, session, transport, network, data link, physical | The layer models |
| TCP/IP model | Application, transport, internet, link: four layers | The layer models |
| Segment, packet, frame, bits | The name of the data at layers 4, 3, 2 and 1 | Encapsulation |
| Ethernet frame | 14-byte header, 46 to 1,500-byte payload, 4-byte FCS | Encapsulation |
| IPv4 / IPv6 header | 20 bytes minimum / 40 bytes fixed | Encapsulation |
| TCP / UDP header | 20 bytes minimum / 8 bytes | Encapsulation |
| MAC address | 48-bit address of a network card, six hex pairs; first half identifies the maker | MAC addresses and frames |
| Ethernet frame | Destination MAC, source MAC, type, 46 to 1,500 bytes of data, 4-byte check | MAC addresses and frames |
| MAC address table | Learned from source addresses; entries age out after 300 s by default | MAC address learning |
| Forward, filter, flood | Known port, same port, unknown destination or broadcast | MAC address learning |
| Cut-through / store-and-forward | Forward after the destination address / check the whole frame first | MAC address learning |
| Duplex mismatch | Link stays up; late collisions on the half side, CRC errors on the full side | Duplex and speed |
show interfaces | Errors, CRC, collisions, speed and duplex on a Cisco port | Duplex and speed |
show cdp neighbors / show lldp neighbors | Which device and port is on the other end | CDP and LLDP |
| Default gateway | The router a host sends to when the destination is not on its own network | The default gateway |
| ARP | Broadcast "who has 10.0.0.1?"; the owner replies with its MAC | ARP |
arp -a / ip neigh | The ARP cache on a host | ARP |
| Remote destination | The host ARPs for its default gateway, not the far host | ARP |
| Routing table | Destination prefix, next hop, outgoing interface | Routing tables |
| Per packet | Check, decrement TTL, look up, rewrite the frame, forward | Routing tables |
| Longest prefix match | A /28 beats a /24 beats a /0 default route | Longest prefix match |
show ip route | C connected, L local, S static, O OSPF, D EIGRP, B BGP | Longest prefix match |
ip route 0.0.0.0 0.0.0.0 203.0.113.1 | Default route | Static and floating routes |
ip route 10.2.0.0 255.255.0.0 10.0.0.2 250 | Floating static: distance 250 waits behind a better route | Static and floating routes |
| Classic faults | Wrong mask, gateway outside the subnet, duplicate address | Troubleshooting addresses |
| IP vs MAC address | IP stays the same end to end; MAC is rewritten at every router | Addresses at each layer |
| Port, IP, MAC | Which program, which host, which network card on this link | Addresses at each layer |
| Subnet | A smaller network cut from a block by lengthening the mask; one more bit halves the block | Borrowing a bit |
| Usable hosts | 2^(32 − prefix) − 2; a /24 has 254 | Subnetting |
| /25 /26 /27 /28 /29 /30 | 126, 62, 30, 14, 6, 2 hosts | Subnetting |
| /31 | Point-to-point link: two addresses, no broadcast | Subnetting |
| Block size | 2 to the power of the host bits, or 256 minus the mask octet; subnets start at its multiples | A worked example |
| Block size | 256 minus the mask's interesting octet; subnets start at its multiples | A worked example |
| VLSM | Assign the largest subnet first, then the next, with no overlap | VLSM |
| Summarisation | Contiguous, aligned blocks: four /24s from .0 become one /22 | Route summarisation |
| 128 bits | Eight groups of four hex digits | The IPv6 address space |
| Shortening | Drop leading zeros; replace one longest run of zero groups with :: | Writing IPv6 addresses |
| /64 | The standard subnet: 64 bits network, 64 bits interface | Prefix and interface ID |
2000::/3 fc00::/7 fe80::/10 ff00::/8 | Global, unique local, link-local, multicast | Prefix and interface ID |
::1 / 2001:db8::/32 | Loopback / documentation | Prefix and interface ID |
| SLAAC | Router advertises the prefix; the host makes its own address | SLAAC |
| NDP messages | ICMPv6 133 RS, 134 RA, 135 NS, 136 NA, 137 redirect | SLAAC |
| Modified EUI-64 | Insert FFFE in the middle of the MAC and flip the seventh bit | SLAAC |
| Dual stack, tunnels, NAT64 | Run both; carry v6 over v4; translate at the edge | IPv4 to IPv6 transition |
| 5-tuple | Protocol, source IP, source port, destination IP, destination port | Ports |
| Port ranges | 0 to 1023 well known, 1024 to 49151 registered, 49152 to 65535 dynamic | Ports |
| SYN, SYN-ACK, ACK | Three-way handshake: one round trip before data | Handshake |
| FIN, TIME-WAIT | Each side closes; the closer waits 2 × MSL | Handshake |
| Sequence numbers | Count bytes, so the receiver asks for exactly what is missing | Reliability |
| MSS | 1,460 bytes on standard Ethernet: 1,500 MTU minus 40 | Reliability |
| Throughput ceiling | Window ÷ round-trip time | Reliability |
| Slow start, fast retransmit | Double each round trip; resend after three duplicate ACKs, halve the window | Reliability |
| UDP | 8-byte header, no handshake, no resend: DNS, VoIP, games, QUIC | UDP |
| Voice budget | 150 ms one way; G.711 is 64 kbps in 20 ms packets | UDP |
| DSCP EF 46 / AF41 34 | Voice / interactive video markings | UDP |
| DNS lookup | Stub asks resolver; resolver asks root, TLD, then the authoritative server | DNS |
| A AAAA CNAME MX NS PTR TXT SRV | IPv4, IPv6, alias, mail, name server, reverse, text, service | DNS |
dig example.com MX / nslookup | Ask DNS directly | DNS |
| DoT 853 / DoH 443 / DNSSEC | Encrypted DNS / signed answers | DNS |
| DHCP DORA | Discover, offer, request, acknowledge; UDP 67 server, 68 client | DHCP |
| T1 / T2 | Renew at 50% of the lease, rebind at 87.5% | DHCP |
ip helper-address | Relay DHCP broadcasts to a server on another subnet | DHCP |
| PAT (NAT overload) | Many private hosts share one public address by port | NAT and PAT |
| Inside local / inside global | The private address / the public address it becomes | NAT and PAT |
ip nat inside source list 1 interface g0/0 overload | Configure PAT on a Cisco router | NAT and PAT |
| NTP UDP 123 | Stratum 1 is next to a reference clock; 16 means unsynchronised | NTP |
| 22 SSH, 25 SMTP, 53 DNS, 80/443 HTTP(S), 3389 RDP | Ports to know by heart | Ports |
| 587 / 993 / 995 | Mail submission / IMAPS / POP3S | Ports |
| SNMPv3, SSH, HTTPS | Manage devices only over encrypted channels; not Telnet or SNMPv1/2c | Device management |
| VLAN | One broadcast domain per VLAN on the same switch | VLANs |
| Normal / extended VLANs | 1 to 1005 / 1006 to 4094 | VLANs |
switchport mode access switchport access vlan 10 | Put a port in one VLAN | VLANs |
| 802.1Q tag | 4 bytes: TPID 0x8100, priority, DEI, 12-bit VLAN ID | 802.1Q trunks |
| Native VLAN | Untagged on the trunk; must match at both ends | 802.1Q trunks |
switchport trunk allowed vlan 10,20 | Limit which VLANs a trunk carries | 802.1Q trunks |
| Router on a stick / SVI | Subinterfaces on one link / a routed VLAN interface on a layer 3 switch | Inter-VLAN routing |
interface vlan 10 ip address … | Create an SVI | Inter-VLAN routing |
| STP timers | Hello 2 s, max age 20 s, forward delay 15 s; RSTP converges in about a second | Spanning tree |
| Root bridge | Lowest bridge ID: priority (default 32768) then MAC | Spanning tree |
| PortFast, BPDU guard | Edge ports go live at once; shut a port that hears a switch | Spanning tree |
| LACP active/passive, PAgP desirable/auto | Two passives or two autos never form a channel | EtherChannel |
| Link-state / distance-vector | Share a map (OSPF, IS-IS) / share directions (RIP, EIGRP) | Dynamic routing |
| OSPF cost | Reference bandwidth ÷ interface bandwidth; lowest total wins | OSPF cost |
| OSPF hello / dead | 10 s / 40 s on broadcast links; must match to become neighbours | Convergence |
224.0.0.5 / 224.0.0.6 | All OSPF routers / designated routers | Convergence |
| DR election | Highest priority, then highest router ID | Convergence |
| Administrative distance | Connected 0, static 1, eBGP 20, EIGRP 90, OSPF 110, RIP 120, iBGP 200 | Administrative distance |
| BGP | Routes between autonomous systems, chosen by policy; about a million IPv4 prefixes | BGP |
| HSRP / VRRP / GLBP | Cisco active-standby / open standard / Cisco load sharing | First-hop redundancy |
| VRRP virtual MAC | `00-00-5E-00-01-{VRID}` | First-hop redundancy |
| Channels 1, 6, 11 | The only three non-overlapping 2.4 GHz channels | 2.4 GHz channels |
| 5 GHz / 6 GHz | 25 / 59 20-MHz channels in the US; DFS on some 5 GHz channels | 2.4 GHz channels |
| Free-space path loss | 20 log10(d km) + 20 log10(f MHz) + 32.44 dB | Signal |
| Wi-Fi 4 / 5 / 6 / 6E / 7 | 802.11n / ac / ax / ax at 6 GHz / be | Wi-Fi standards |
| SSID / BSSID | The network's name / one access point radio's MAC | SSID and roaming |
| WPA3 Personal / Enterprise | SAE password exchange / 802.1X, a key per user | Wireless security |
| CAPWAP UDP 5246 / 5247 | Controller to lightweight AP: control / data | Controllers |
| −67 dBm, 25 dB SNR | Targets for voice-grade Wi-Fi | Site survey |
| Site survey | Overlap cells 15 to 20%, never on the same channel | Site survey |
| ACL rules | Top to bottom, first match wins, implicit deny at the end | ACLs |
| Standard / extended ACL | 1 to 99, source only, near the destination / 100 to 199, near the source | ACLs |
| Wildcard mask | Inverse of the subnet mask: 0.0.0.255 matches a /24 | ACLs |
| Stateful firewall | Allows replies to conversations it saw start | Firewalls |
| IPsec ESP 50, IKE UDP 500, NAT-T UDP 4500 | Site-to-site VPN protocols and ports | VPNs |
| 802.1X | Supplicant, authenticator (switch), authentication server (RADIUS) | Access control |
| RADIUS UDP 1812/1813 / TACACS+ TCP 49 | Network logins / device admin with per-command authorisation | Access control |
| DHCP snooping, DAI, port security | Stop rogue DHCP, ARP spoofing and MAC flooding | Layer 2 security |
switchport port-security maximum 2 | Allow at most two MAC addresses on a port | Layer 2 security |
| Zero trust | Never trust by network location; check every request | Threats |
| Access, distribution, core | The three campus tiers; small sites collapse the top two | Campus design |
| Spine-leaf | Every leaf connects to every spine: any server is two hops from any other | Data centre fabric |
| VXLAN | Layer 2 over UDP 4789, 24-bit ID (16 million segments), 50 bytes of overhead | Data centre fabric |
| Load balancer / CDN | Spread requests across servers / serve content near the user | Scaling services |
| SDN | Control plane in a controller; devices forward | SDN |
| REST verbs | GET read, POST create, PUT replace, PATCH change, DELETE remove | SDN |
| Ansible | Agentless over SSH, YAML playbooks, 5 hosts at a time by default | Automation |
| SD-WAN | Picks the best link per application, right now | SD-WAN |
| VPC | Subnets, route tables, internet and NAT gateways; AWS keeps 5 addresses per subnet | Cloud networks |
| Security group / network ACL | Stateful, on the instance / stateless, on the subnet | Cloud networks |
| VPC peering | Not transitive; use a transit gateway for many VPCs | Cloud networks |
| Seven steps | Identify, theory, test, plan, implement, verify, document | Method |
| Bottom up, top down, divide | Ping splits the problem in half | Layers |
ping / traceroute ( tracert ) | Reachability / each hop, by raising TTL from 1 | Ping and traceroute |
! . U | Cisco ping: reply, timeout, unreachable | Ping and traceroute |
| CRC errors / late collisions | Cabling or interference / duplex mismatch | Interface counters |
tcpdump -i eth0 port 53 | Capture what really crossed the wire | Packet capture |
| Syslog severities 0 to 7 | Emergency, alert, critical, error, warning, notice, info, debug | Logs and monitoring |
| SNMP, NetFlow/IPFIX | Device counters / who talked to whom, how much | Logs and monitoring |
| Toner, cable tester, Wi-Fi analyser | Find, test and see the medium | Symptoms |
Nothing matches. Try a shorter word.